Exactly How to Install a Tub Yourself: Removing and Replacing.
Exactly How to Install a Tub Yourself: Removing and Replacing.
Blog Article
On this page below you might get some sound expertise all about How to Install a Bathtub Yourself.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This short article will assist you set up a new bath tub in your bathroom if you have currently gotten a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the tub as well as additionally check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its final position.
Getting ready for the Installment
To start with, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, bring about issues with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Sharing is caring. Helping people is fun. Kudos for your time. Visit us again soon.
Suggested Site Report this page